![]() Hopefully our guide on how to jump start your van has given you some useful tips about what to do if you are faced with a flat battery when you are out and about in your van.6) Mark On “Show Characters” and the Password of the Wifi Network is Shown: However, if the battery becomes flat again after the jump start procedure, it could mean that the battery is faulty or damaged and might need replacing. Once your vehicle is running then you should drive it for a minimum of 20 minutes in order to charge the battery, or once you are home connect the battery to a charger overnight. ![]() If it does start then congratulations you have managed to jump start your van! Try again and leave it charging for longer. > Start the ignition of your van if it won't start now then you might not have left it to charge long enough. > Finally disconnect the (+) positive red cable from the (+) positive terminal on the van which had the flat battery. ![]() > Next disconnect the (+) positive red cable from the (+) positive terminal on the vehicle you used to help jump start your van. > Then disconnect the (-) negative black cable from the (-) negative terminal on the vehicle you used to help jump start your van. > Start by disconnecting the (-) negative black cable from the earthing point. > First of all you need to switch the engines of both vehicles off and you need to be careful when you are removing the jump leads, DO NOT let any jump leads touch any metal especially the bodywork of the vehicles when removing them. > Once you van has been jump started and is running the jump leads need to be removed in reverse order. > If your van still doesn't turn on, then depending on where you are you should call your breakdown provider who will attempt to fix your vehicle at the roadside. > Once your van is running leave the engine of both vehicles on for five minutes to charge the battery. > Try and start your van, if it doesn't turn on then wait for a couple of minutes before trying again. > Revving the engine a little will help to produce more current for the battery. > Start the engine on the working vehicle and let the engine run for a couple of minutes. > Ensure all the heaters and radios are switched off, so all of the energy of the working vehicle is used for the jump start. Use the image below as a guide to connecting the jump leads. (Some vans have negative jump starting poles just for this situation, check your vehicle handbook to see if yours does.) ![]() > Identify the positive and negative ends of both batteries (the positive end will usually have a plus symbol or red markings, whereas the negative end will have a minus symbol or black markings).Ī) Using the jump leads connect one end of the (+) positive red cable to the (+) positive terminal on the dead battery.ī) Then connect the other end of the (+) positive red cable to the (+) positive terminal on the working vehicle.Ĭ) Take the (-) negative black cable and connect to the (-) negative terminal on the working vehicle.ĭ) Take the other end of the (-) negative black cable and connect it to a suitable earthing point such as metal bolt or bracket under the bonnet, however make sure it is away from the dead battery and the fuel system of your van. > Make sure both engines are switched off and open the bonnets. Make sure that the vehicles do not touch as it could cause a shortage (and a bang). > Ask the owner of the working vehicle to park it opposite your van so that the bonnets are facing. > Keep metal objects away from the battery. ![]() > Don't smoke or have any naked flames in the vicinity. > Make sure you secure all loose clothing before jump starting your van. When jump starting your vehicle there are a few safety issues which you need to be aware of: Any specific instructions should be used instead of our steps. Remember you always need to read your vehicle handbook and instructions to any equipment before you jump start your van. > Another vehicle with the same battery voltageįor safety it is important to remember not to attempt to jump start your van if the battery frozen, cracked or damaged in these cases it is best to be safe and call a professional. If you're not sure how to do this just follow our simple steps and you'll be on the move again in no time. Whether you've left the lights on, the keys in the ignition or your battery is faulty, having to jump start a van to get the engine running can be a daunting experience. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |